#This file contains log message templates (en) for the N8000 project

#Format: <Message ID> <tab(s) or whitespace(s)> <Message string>
#Leading '#' are comments, empty lines are ignored

#General Log Messages
0	%1
1	Masterfault ok: %1
2	Masterfault failure: %1
3	process exiting ...
4	process started (%1)

#Log Messages for ADC
5	AD converter failure
6	AD converter ok

#Log Messages for CAN Bus
7	error starting CAN Interface
8	CAN Bus Active
9	CAN bus scan failed!
10	CAN bus scan ready, baudrate: %1 kBaud
11	CAN Bus started, Baudrate = %1 kBaud
12	set CAN bus baudrate to %1 kBaud
13	received: CAN Bus RESET command
14	starting CAN bus scan
15	automatic CAN Bus RESET
16	CAN Bus high bandwidth usage: %1 percent
17	CAN Bus Passive
172 CAN Bus light

#Log Messages for CN
18	Auto-Sync on => changed Sync-Source from CobraNet to internal DSP Osc.
19	CM-1 fatal error
20	CM-1 general fault
21	CM-1 interface error
22	CM-1 mute fault
23	CM-1 Rx fault
24	CM-1 Tx fault
25	CM-1 watchdog out of range (Ref_Max: %1, Ref_Min: %2, counter: %3)
26	CM-1 watchdog overflow
27	deactivate CM-1 due to successive errors
28	CM-1-HMI (Host Interface): %1 wait for %2 (Address %3)
29	no CM-1 detected after reset
30	CM-1 detected
31	no CM-1 detected
32	CM-1 reset
155	no reception of In-Bundle[%1] with number %2
156	no transmission of Out-Bundle[%1] with number %2

#Log Messages for CONFIGDATA
33	(%1) configuration block Nr %2 => invalid config data
34	(%1) configuration block Nr %2: invalid block-id (%3)
35	(%1) preset %2 has invalid data: ErrNo: %3
36	configuration change failed
37	copy preset data to /ram (ErrNo: %1) failed
38	couldn't read configuration file %1
39	couldn't read configuration file %1 => using defaults
40	configuration file (%1) read error
41	error configuration building
42	file %1 has incompatible configuration-id (%2)
43	file %1 has invalid crc32 value
44	invalid CRC check for configuration file
45	no base configuration file => using defaults
46	no blockcode for Main-DSP %1
47	no memory allocation (%1)
48	open file %1 (ErrNo: %2) failed
49	read from preset file failed
50	save configuration data to %1 (ErrNo: %2) failed
51	save preset data to %1 (ErrNo: %2) failed
52	writing to base configuration file failed
53	read from file %1 failed
54	---

#Log Messages for DSP
55	Sync-Signal from slot %1 not available and Auto-Sync = off
56	Sync-Signal from slot %i is not available & Auto-Sync = on =>, Sync-Source = internal DSP Osc.
57	switching DSP-System from state "Reset" to state "Audio-Off" failed
58	not both DSPs on DSP-Board detected
59	booting DSP-System failed
60	start signal processing in slot %1 failed
61	stop signal processing in slot %1 failed
62	DSP watchdog failure in slot %1
63	init CS8416 %1 read-buffer slot %2 device %3 failed
64	init SPI read-buffer slot %1 failed
65	init/read back CS8416 slot %1 device %2 failed
66	DSP-OS in slot %1 not running
67	DSP-Delay-RAM clear in slot %1 failed
68	%2 words in DSP-Delay-RAM (slot %i) defect
69	starting DSP-routine RAM-Clear failed
70	sync_boot-init/read back CS8416 slot %1 device %2 failed
71	sync_set_boot-init CS8416 read-buffer slot %1 device %2 failed
72	couldn't open NCP connection
73	couldn't open SPI device for DSPs
74	couldn't open SPI device for slot %1
75	couldn't open SPI device for Sync
76	no memory allocation for event handling
77	no memory allocation for static array read/write table
78	fatal error (select)! Terminating ...
79	DSP-System booted up successful (cycles: %1)
80	%1 in slot %2 detected
81	DSP in slot %1: unknown typ (%2)
82	DSP-OS in slot %1 failed after restart
157	couldn't open Power-Fail device
158	Reset DSP-System/CobraNet due to Power-Fail

#Log Messages for HWCONFIG
83	slot %1 not assembled, but should
84	slot %1 incorrect assembled
85	extension slot %1 not assembled, but should
86	CM-1 not assembled, but should

#Log Messages for MACRO
87	Macro %1 (type %2) started by %3

#Log Messages for NCP
88	---
89	NCP filetransfer error: %1 %2
90	NCP filetransfer: read error
91	NCP filetransfer: read timeout
92	NCP filetransfer: write error
93	open file %1 (%2) failed
94	couldn't init NCP abbos, exiting ...
95	couldn't init authentication, exiting ...
96	---
97	logout: %1:%2
98	NCP filetransfer: read %1
99	NCP filetransfer: write %2
100	NCP filetransfer: write timeout
101	NCP filetransfer: transfer pending
102	---
103	%1 login: %2:%3
104	%1 login: %2:%3, max login count exceeded: %4
105	%1 login: %2:%3, wrong password

#Log Messages for NML
106	couldn't initialize RS232 for fault check
107	initialization failed! Terminating ...
108	shared memory Error! Terminating ...
109	adjust time from daylight savings time to normal time
110	adjust time from normal time to daylight savings time
111	detected booter version: %1
112	detected firmware version: %1
113	rebooting system ...
114	received signal, terminating
115	starting process %1, NCP PID %2
116	stopping process %1, NCP PID %2
117	couldn't calculate date for daylight savings time begin
118	couldn't calculate date for for daylight savings time end
119	couldn't set time, invalid format
120	coudn't start process %1, NCP PID %2

#Log Messages for Parser
121	%1(%2, %3) started at %4

#Log Messages for PTD
122	pilot tone absent

#Log Messages for RCM
123	NCP request queue overflow
124	error allocating CAN buffers, exiting
125	---
126	---
127	---

#Log Messages for Remote
128	N8000 device %1 (ip %2 port %3) state %4
129	N8000 slave control: login timeout
130	callbackRemoteStatus: error response (%1)
131	N8000 slave control: %1 error response (%2)
132	N8000 slave control: %1 response (%2)

#Log Messages for RS232
133	RS232 check port%1 failed!
134	initialized %1 for faultcheck with %2%3%4%5

#Log Messages for USERFAULT
135	User Fault #%1 is %2

#additional
136	voltage (%1) failure!
137	voltage (%1) ok!
138	GPI check#%1 %2 failure!
139	GPI check#%1 %2 ok!
140	RS232 check port %1 ok!
141	chassis temperature %1C exceeded maximum (%2C)!

142 CAN Bus Off!

#Log Messages for CONFIGDATA/Power-up-Preset
143	Power-up-Preset read failed
144	Power-up-Preset has invalid data
145	deactivate Power-up-Preset due to an error
146	PwrUpPrstObjectWr: problems while reading datasize of preset diff
147	try to overwrite object (id: %d) with different data length
148	Power-up-Preset (%1) is full! Not all data could be saved
149	deactivate Power-Up-Preset due to write problems to hashtable in FRAM
150     Power-up-Preset size (hashsize) in FRAM exceeds %1 limit

#additional Log Messages for DSP
151	not both DSPs on Extension-Board detected
152	DSP-OS in slot %1 not running after boot-sequence
153	DSP no. %1 not detected on DSP-Board
154	%2 words in DSP-Delay-RAM (slot %i) defect

#Log Messages for database
159 could not connect to local database fifo

//#Log messages for wallpanels
160 PWS [%1] detected
161 no memory in database left for PWS [%1]
162 PWS [%1] deallocated
163 PWS [%2] does not answer our request for %1
164 PWS [%1] has problems while updating
165 PWS [%1] has wrong firmware version: %2

//#Log messages for dcs801r
#166 DCS [%1] detected
#167 no memory in database left for DCS [%1]
#168 DCS [%1] deallocated
#169 DCS [%1] does not answer our request for %2
#170 DCS [%1] has no problems while updating
#171 DCS [%1] has wrong firmware version: %2

//#Log messages for taskEngine

