V Series
Go compact, amplify smart
- Four-channel and two-channel amplifiers, with a total powerTANK capacity of 600 W
- Variable Load Drive (VLD) providing the same power into 4 Ω, 8 Ω, 70 V or 100 V
- ecoRAIL and APD deliver significant reduction in power consumption
- dualCOOL convection cooling with additional intelligent fan in case of extreme thermal conditions
Designed with commercial applications in mind, V Series models are ideal for small to mid-sized installation scenarios. These compact amplifiers are not only designed for background music and announcements – they also excel when higher SPL levels are needed. Equipped with a range of cutting-edge Dynacord technologies to ensure flawless, silent operation and energy-saving, flexible power consumption, the V Series features two- and four-channel versions with different footprints that make them perfectly suited for a variety of installations.
Dynacord powerTANK technology adds even more installation flexibility, working like a power reservoir for the amplifier. With direct access to the total power of 600 watts, V Series can deliver asymmetric power across all channels as needed. There is no waste of energy, which allows great flexibility – especially when driving multiple audio zones with different loads. For example, a single V600:4 can simultaneously serve as system drive for the compact loudspeakers in a small zone (such as a kitchen area) as well as for larger loudspeakers (such as in an auditorium). Contributing to the ease of installation, this feature does not require any special configuration skills – powerTANK engages automatically. In conjunction with a DSP matrix – such as the Dynacord MXE5-64 Matrix Mix Engine – V Series amplifiers can also be specified for larger distributed installations working as a distribution amplifier for smaller zones.
Models
V600:2 |
 V600:4 |
|
| ELECTRICAL | ||
| Total rated output power1 | 600 W | |
| Number of channels | 2 | 4 |
| Rated output power1 | 2 x 300 W | 4 x 150 W |
| Output power: | 4 Ω / 8 Ω / 70 V / 100 V | |
| Maximum output power per channel (power sharing) | 500 W / 600 W / 500 W / 600 W | |
| AMPLIFIER | ||
| 4 Ω / 8 Ω / 70 V / 100 V | ||
| Nominal Gain (+6 dBu input sensitivity, LEVEL 0 dB) |
27.0 dB / 30.0 dB / 33.2 dB / 36.2 dB | 24.0 dB / 27.0 dB / 33.2 dB / 36.2 dB |
| Signal to Noise Ratio (A‑weighted, ref. to rated output power, LEVEL 0 dB) |
> -100 dB / > 102 dB / > 101 dB / > 103 dB | > -98 dB / > 100 dB / > 101 dB / > 103 dB |
| THD+N (1/8 RATED OUTPUT POWER, 1 KHZ) |
< 0.1 % | |
| CONNECTIVITY | ||
| Type | 1 x 6-pin Euroblock, 3.81 mm, male, parallel 1x RJ45 (AES72-1E) |
2 x 6-pin Euroblock, 3.81 mm, male, parallel 1x RJ45 (AES72-1E) |
| Loudspeaker output | 2 x 4-pin Euroblock, 5.08 mm, female | |
| Control port type | 1 x 5-pin Euroblock, 3.81 mm, male | |
| GENERAL | ||
| Signal processing | Input Routing, Filter (24 dB/Oct.), Hi-pass 30/50/100/150 Hz, Lo-pass 150 Hz, Peak Limiter | |
| Power requirements | 100 V to 240 V, 50 Hz to 60 Hz AC | |
| Power consumption: | ||
| Idle mode (ecoRAIL with no input signal) | < 12 W | < 20 W |
| Consumption at 1/8 rated output power | 115 W | |
| Standby mode (APD active) | < 1 W | |
| Protections | Audio limiters, high temperature, DC, HF, short circuit, back-EMF, peak current limiters, inrush current limiters, mains over/under voltage protection | |
| 1 Test signal for max. output power according IHF-A-202 (Dynamic-Headroom, burst 1 kHz / 20 ms on / 480 ms off / low level -20 dB) | ||
Downloads
Where to Buy
Install Sound Partners
Dynacord together with our certified partners, are ready to help support you through planning, purchase, and setup. Services available through our network of highly-qualified associates and partners may include:
- System Design
- Installation
- Programming & Commissioning
Warranty & After Sales Programs