Powered Mixers

DIM 30

<0.05%

Crosstalk

Amplifier Ch1/Ch2: < -85dB; Channel to channel: < -78dB

Frequency Response (-3 dB)

Any input to any Mixer output: 15–22000Hz; Any input to Speaker output: 20–22000Hz

Signal-to-Noise Ratio (A-weighted)

104

Power Consumption

180W

Cooling

Continuous speed controlled fan

Height

244

Width

395

Depth

241

Weight Net

4.9

Input Sensitivity

MIC: -65dBu (435μV); LINE (mono): -45dBu (4.35mV); LINE (stereo): HI: -27dBu (34.6mV), LO: -11dBu (218mV); CD (stereo): -27dBu (34.6mV)

Displays

128 x 64 pixels, LCD

Maximum Output Voltage

Dual channel mode: 52Vrms; Direct Drive mode: 100Vrms

Phantom Power

48VDC

Shipping Weight

6.4

Output Stage Topology, amplifier

Class D

Operating Temperature Range

5° to 40°C (40° to 105°F)

Max. dual channel output power, dynamic headroom, IHF-A

into 4Ω: 2 x 600W; into 8Ω: 2 x 340W;

Rated output power (*rated load) THD < 0.2%, 20Hz – 20kHz

into 4Ω: 400W; into 8Ω: 240W

Max. output power, Direct Drive mode (bridge configuration), continuous, 1 kHz, THD = 1%

into 12Ω: 680W

Transducer

dBu, typical

Microphone mute switch attenuation

>100dB

Channels

5

Channel VOL and FX/AUX send attenuation

>85dB

Auxiliarys (MON, FX, AUX)

1 Post, 1 Pre

Max. level, mixing desk, input VOL down, output VOL up

MIC inputs, GAIN @ min. position: +11dBu; Mono line inputs, GAIN @ min. position: +30 dBu; Stereo line inputs: +26dBu; PHONES output: +21dBu; MASTER A, B, AUX outputs: +11dBu

CMRR, MIC input, 1 kHz

>80dB

Master EQ 7-band (63, 160, 400, 1k, 2.5k, 6k, 12k Hz)

±10dB / Q =1.5

Input Impedances

MIC: 2㏀; CD: 10㏀; All other inputs: > 15㏀

Delay MASTER B, selectable

0–145ms (0–50m)

Output Impedances

PHONES: 47Ω; All other outputs (impedance balanced): 150Ω

Audio player (USB at front panel)

Switching mode power supply (μC controlled): FAT 32; Supported audio file formats: MP3, WAV; Interface: USB2.0, female type A; USB power supply, max. rated current (short circuit proof): 5 V, 500 mA;

Equivalent Input Noise, MIC input, A-weighted, 150 ohms

-129dBu

AC power input

100–240VAC, 50–60Hz

Noise, Channel inputs to Master A L/R outputs, A-weighted

MASTER VOLUME down: -99dBu; MASTER VOLUME center, all channel volume down: -90dBu; MASTER VOLUME center, all channel volume center: -85dBu

Equalization

Low shelving filter: ±15dB / 60Hz; Mid peak filter: ±12dB / 2.4kHz; High shelving filter: ±15dB / 12kHz

Filter

Low-cut filter, microphone processing (switchable): 80Hz, 18dB/oct. or 150Hz, 12 dB/oct; Low-cut filter, amplifier (engaged in Direct Drive mode): 50Hz or 70Hz, 18dB/oct; Speaker processing: LPN, switchable

Effects

Type: Stereo 24/48-bit multi effects processor; Effect presets: 32 factory presets, user editable; Remote control: Footswitch

Digital Audio Interface

Channels: 2 in, 2 out; AD/DA conversion: 16-bit, delta-sigma; Sampling rate: 32/44.1/48kHz; PC interface: USB2.0, female type B

Protection

MASTER A, B, AUX outputs: Adjustable peak limiters, -10 – +11dBu; Amplifier: Audio limiters, high temperature, DC, HF, short circuit, peak current limiters, turn-on delay, back EMF; Switching mode power supply (μC controlled): Inrush current limiters, ma

Safety Class

I

Max. Single Channel Output Power, Dynamic-Headroom, IHF-A

into 4Ω: 640W; into 8Ω: 350W

Max. Single Channel Output Power, Continuous, 1 kHz, THD = 1%

into 4Ω: 500W; into 8Ω: 280W

Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel

into 4Ω: 2 x 450W; into 8Ω: 2 x 270W;

IMD-SMPTE, power amplifier, 60 Hz, 7 kHz

<0.15%

Total Harmonic Distortion

MIC input to master A L/R outputs, +10dBu, typical: < 0.015%; MIC input to speaker output: < 0.15%

Input Connections

5 x XLR/Jack socket

DIM 30

<0.05

Crosstalk

Amplifier L/R: < -85dB; Channel to Channel: < -80 dB; Mute- and Standby-Switch attenuation: > 100 dB; Fader and FX/AUX/MON-Send attenuation: > 85dB

Frequency Response (-3 dB)

Any input to any Mixer output: 15Hz to 70kHz; Any input to Speaker L/R output: 20Hz to 30kHz

Signal-to-Noise Ratio (A-weighted)

105

Power Requirement

100V to 240 VAC, 50Hz to 60Hz

Power Consumption

450W

Cooling

Continuous speed controlled Fans

Height

161.7

Width

438.8

Depth

362.5

Weight Net

9.5

Max. Single Channel Output Power, Continuous, 1 kHz, THD = 1%

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1150W; into 8Ω: 2 x 650W

Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1000W; into 8Ω: 2 x 600W

IMD-SMPTE, power amplifier, 60 Hz, 7 kHz

<0.15%

Output Stage Topology, amplifier

Class D

Output Power Control (Speaker Protection)

Adjustable longterm RMS Limiter

Maximum Output Voltage

74 Vrms

Total Harmonic Distortion

MIC input to Master A L/R outputs, +16dBu, typical: < 0.005%; POWER AMP INPUTS to Speaker L/R outputs: < 0.075%

Phantom Power

48VDC

Input Connections

6

Shipping Weight

12

Input Sensitivity

MIC: -74dBu (155μV); LINE (Mono): -54dBu (1.55mV); LINE (Stereo): -34dBu (15.5mV); CD (Stereo): -34dBu (15.5mV); POWER AMP INPUTS: +8dBu (1.95V)

Operating Temperature Range

+5 °C…+40 °C (40 °F…105 °F)

Rated output power (*rated load) THD < 0.2%, 20Hz – 20kHz

into 4Ω: 2 x 900W; into 8Ω: 2 x 450W

Displays

128 x 64 pixels, OLED

Maximum SPL

MIC inputs: +11dBu; Mono Line inputs: +31 dBu; Stereo Line inputs: +31dBu; All other inputs: +22dBu; All other outputs: +22dBu

Channels

4

Auxiliarys (MON, FX, AUX)

1 Pre, 1 Post, 1 Pre/Post switchable

CMRR, MIC input, 1 kHz

>80dB

Input Impedances

MIC: 2㏀; CD In: 10㏀; All other inputs: > 15㏀

Output Impedances

Phones: 47Ω; All other outputs (balanced/unbalanced): 150Ω / 75Ω

Equivalent Input Noise, MIC input, A-weighted, 150 ohms

-130dBu

Noise, Channel inputs to Master A L/R outputs, A-weighted

Master fader down: -100dBu; Master fader 0dB, Channel fader down: -92dBu; Master fader 0dB, Channel fader 0dB, Channel gain unity: -82dBu

Equalization

LO Shelving: ±15dB / 60Hz; MID Peaking: ±12dB / 2.4kHz; HI Shelving: ±15dB / 12 kHz; Master EQ 9-band (63, 125, 250, 500, 1k, 2k, 4k, 6.3k, 12kHz): ±10dB/Q = 1.5 to 2.5

Filter

LO-CUT, mono inputs: f = 80Hz, 18dB/oct., switchable; Speaker Processing: LPN, switchable

Effects

Type: 2x Stereo 24/48-bit multi effects processors; Effects presets: 100 Factory + 20 User, Tap-Delay; Remote control: Footswitch, MIDI

Digital Audio Interface

Channels: 4 In / 4 Out; AD/DA Conversion: 24-bit; Sampling Rate: 44.1 / 48 / 88.2 / 96kHz; PC Interface: USB2.0, Female Type B; Peak Display: 6 dB before Clip

MIDI Interface

5-pin DIN connector, In / Out

Protection

Mixer Outputs, relay controlled: AUX, MON, MASTER A L/R; Amplifier: Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Turn-on Delay, Back EMF; Switching Mode Power Supply (μC controlled): Inrush Current Limiters, Mains Over/U

Safety Class

I

Max. Single Channel Output Power, Dynamic-Headroom, IHF-A

into 2.66Ω: 2 x 1600W; into 4Ω: 2 x 1250W; into 8Ω: 2 x 675W

DIM 30

<0.05%

Crosstalk

Amplifier L/R: < -85dB; Channel to Channel: < -80 dB; Mute- and Standby-Switch attenuation: > 100 dB; Fader and FX/AUX/MON-Send attenuation: > 85dB

Frequency Response (-3 dB)

Any input to any Mixer output: 15Hz to 70kHz; Any input to Speaker L/R output: 20Hz to 30kHz

Signal-to-Noise Ratio (A-weighted)

105dB

Power Requirement

100V to 240VAC, 50Hz to 60Hz

Power Consumption

450W

Cooling

Continuous speed controlled Fans

Height

164.5

Width

510.5

Depth

571.5

Weight Net

14

Displays

128 x 64 pixels, OLED

Maximum Output Voltage

74 Vrms

Phantom Power

48VDC

Shipping Weight

17

Operating Temperature Range

+5 °C…+40 °C (40 °F…105 °F)

Rated output power (*rated load) THD < 0.2%, 20Hz – 20kHz

into 4Ω: 2 x 900W; into 8Ω: 2 x 450W

Maximum SPL

MIC inputs: +21dBu; Mono Line inputs: +41dBu; Stereo Line inputs: +30dBu; All other inputs: +22dBu; All other outputs: +22dBu

Channels

6

Auxiliarys (MON, FX, AUX)

2 Pre, 2 Post, 2 Pre/Post switchable

CMRR, MIC input, 1 kHz

>80dB

Input Impedances

MIC: 2㏀; Insert Return: 3.3㏀; 2Track Return & CD In: 10㏀; All other inputs: > 15㏀

Output Impedances

Phones: 47Ω; All other outputs: 75Ω (unbalanced), 150Ω (balanced)

Equivalent Input Noise, MIC input, A-weighted, 150 ohms

-130dBu

Safety Class

I

Noise, Channel inputs to Master A L/R outputs, A-weighted

Master Fader down: -97dBu; Master fader 0dB, Channel fader down: -91dBu; Master fader 0dB, Channel fader 0dB, Channel gain unity: -83dBu

Max. Single Channel Output Power, Dynamic-Headroom, IHF-A

into 2.66Ω: 2 x 1600W; into 4Ω: 2 x 1250W; into 8Ω: 2 x 675W

Equalization

LO Shelving: ±15dB / 60Hz; MID Peaking, mono inputs: ±15dB / 100Hz to 8kHz; MID Peaking, stereo inputs: ±12 dB / 2.4 kHz; HI Shelving: ±15 dB / 12 kHz; Master EQ 11-band (63, 125, 250, 400, 630, 1k, 1.6k, 2.5k, 4k, 6.3k, 12kHz): ±10dB/Q = 1.5 to

Filter

LO-CUT, mono inputs: f=80Hz, 18dB/oct.; VOICE FILTER, mono inputs: switchable; FEEDBACK FILTER, MON ½: 70Hz to 7kHz, Notch, -9dB; Speaker Processing: LPN, switchable

Max. Single Channel Output Power, Continuous, 1 kHz, THD = 1%

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1150W; into 8Ω: 2 x 650W

Effects

Type: Dual stereo 24/48-bit multi effects processors; Effects presets: 100 Factory + 20 User, Tap-Delay; Remote control: Footswitch, MIDI

Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1000W; into 8Ω: 2 x 600W

Digital Audio Interface

Channels: 4 In / 4 Out; AD/DA Conversion: 24-bit; Sampling Rate: 44.1 / 48 / 88.2 / 96kHz; PC Interface: USB2.0, Female Type B; Peak Display: 6 dB before Clip

IMD-SMPTE, power amplifier, 60 Hz, 7 kHz

<0.15%

MIDI Interface

5-pin DIN connector, In / Out

Output Stage Topology, amplifier

Class D

Protection

Mixer Outputs (Relay controlled): MON 1, MON 2, MASTER A; Amplifier: Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Turn-on Delay, Back EMF; Switching Mode Power Supply (μC controlled): Inrush Current Limiters, Mains Over/

Output Power Control (Speaker Protection)

Adjustable longterm RMS Limiter

Total Harmonic Distortion

MIC input to Master A L/R outputs, +16dBu, typical: < 0.005%; POWER AMP INPUTS to Speaker L/R outputs: < 0.075%

Input Sensitivity

MIC: -74dBu (155μV); LINE (Mono): -54dBu (1.55mV); LINE (Stereo): -34 dBu (15.5mV); CD (Stereo): -34dBu (15.5mV); POWER AMP INPUTS: +8dBu (1.95V)

DIM 30

<0.05%

Crosstalk

Amplifier L/R: < -85dB; Channel to Channel: < -80dB; Mute- and Standby-Switch attenuation: > 100 dB; Fader and FX/AUX/MON-Send attenuation: > 85dB

Frequency Response (-3 dB)

Any input to any Mixer output: 15Hz to 70kHz; Any input to Speaker L/R output: 20Hz to 30kHz

Signal-to-Noise Ratio (A-weighted)

105dB

Power Requirement

100V to 240VAC, 50Hz to 60Hz

Power Consumption

450W

Cooling

Continuous speed controlled Fans

Height

164.5

Width

663.5

Depth

571.5

Weight Net

17

Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1000W; into 8Ω: 2 x 600W

Input Sensitivity

MIC: -74dBu (155μV); LINE (Mono): -54dBu (1.55mV); LINE (Stereo): -34dBu (15.5mV); CD (Stereo): -34dBu (15.5mV); POWER AMP INPUTS: +8dBu (1.95V)

IMD-SMPTE, power amplifier, 60 Hz, 7 kHz

<0.15%

Output Stage Topology, amplifier

Class D

Displays

128 x 64 pixels, OLED

Output Power Control (Speaker Protection)

Adjustable longterm RMS Limiter

Maximum Output Voltage

74 Vrms

Phantom Power

48VDC

Shipping Weight

20

Operating Temperature Range

+5 °C…+40 °C (40 °F…105 °F)

Rated output power (*rated load) THD < 0.2%, 20Hz – 20kHz

into 4Ω: 2 x 900W; into 8Ω: 2 x 450W

Maximum SPL

MIC inputs: +21 dBu; Mono Line inputs: +41dBu; Stereo Line inputs: +30dBu; All other inputs: +22dBu; All other outputs: +22dBu

Channels

12

Auxiliarys (MON, FX, AUX)

2 Pre, 2 Post, 2 Pre/Post switchable

CMRR, MIC input, 1 kHz

>80dB

Input Impedances

MIC: 2㏀; Insert Return: 3.3㏀; 2Track Return & CD In: 10㏀; All other inputs: > 15㏀

Output Impedances

Phones: 47Ω; All other outputs: 75Ω (unbalanced), 150Ω (balanced)

Equivalent Input Noise, MIC input, A-weighted, 150 ohms

-130dBu

Noise, Channel inputs to Master A L/R outputs, A-weighted

Master fader down: -97dBu; Master fader 0dB, Channel fader down: -89dBu; Master fader 0dB, Channel fader 0dB, Channel gain unity: -82dBu

Equalization

LO Shelving: ±15dB / 60Hz; MID Peaking, mono inputs: ±15dB / 100Hz to 8kHz; MID Peaking, stereo inputs: ±12 dB / 2.4 kHz; HI Shelving: ±15 dB / 12 kHz; Master EQ 11-band (63, 125, 250, 400, 630, 1k, 1.6k, 2.5k, 4k, 6.3k, 12kHz): ±10dB/Q = 1.5 to

Filter

LO-CUT, mono inputs: f=80Hz, 18dB/oct.; VOICE FILTER, mono inputs: switchable; FEEDBACK FILTER, MON ½: 70Hz to 7kHz, Notch, -9dB; Speaker Processing: LPN, switchable

Effects

Type: Dual stereo 24/48-bit multi effects processors; Effects presets: 100 Factory + 20 User, Tap-Delay; Remote control: Footswitch, MIDI

Digital Audio Interface

Channels: 4 In / 4 Out; AD/DA Conversion: 24-bit; Sampling Rate: 44.1 / 48 / 88.2 / 96kHz; PC Interface: USB2.0, Female Type B; Peak Display: 6 dB before Clip

MIDI Interface

5-pin DIN connector, In / Out

Protection

Mixer Outputs (Relay controlled): MON 1, MON 2, MASTER A; Amplifier: Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Turn-on Delay, Back EMF; Switching Mode Power Supply (μC controlled): Inrush Current Limiters, Mains Over/

Safety Class

I

Total Harmonic Distortion

MIC input to Master A L/R outputs, +16dBu, typical: < 0.005%; POWER AMP INPUTS to Speaker L/R outputs: < 0.075%

Max. Single Channel Output Power, Dynamic-Headroom, IHF-A

into 2.66Ω: 2 x 1600W; into 4Ω: 2 x 1250W; into 8Ω: 2 x 675W

Max. Single Channel Output Power, Continuous, 1 kHz, THD = 1%

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1150W; into 8Ω: 2 x 650W

DIM 30

<0.05%

Crosstalk

Amplifier L/R: < -85dB; Channel to Channel: < -80 dB; Mute- and Standby-Switch attenuation: > 100 dB; Fader and FX/AUX/MON-Send attenuation: > 85dB

Frequency Response (-3 dB)

Any input to any Mixer output: 15Hz to 70kHz; Any input to Speaker L/R output: 20Hz to 30kHz

Signal-to-Noise Ratio (A-weighted)

105dB

Power Requirement

100V to 240VAC, 50Hz to 60Hz

Power Consumption

450W

Cooling

Continuous speed controlled Fans

Height

155

Width

818.5

Depth

498.5

Weight Net

18

Max. Single Channel Output Power, Continuous, 1 kHz, THD = 1%

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1150W; into 8Ω: 2 x 650W

Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel

into 2.66Ω: 2 x 1350W; into 4Ω: 2 x 1000W; into 8Ω: 2 x 600W

IMD-SMPTE, power amplifier, 60 Hz, 7 kHz

<0.15%

Output Stage Topology, amplifier

Class D

Output Power Control (Speaker Protection)

Adjustable longterm RMS Limiter

Total Harmonic Distortion

MIC input to Master A L/R outputs, +16dBu, typical: < 0.005%; POWER AMP INPUTS to Speaker L/R outputs: < 0.075%

Input Sensitivity

MIC: -74dBu (155μV); LINE (Mono): -54dBu (1.55mV); LINE (Stereo): -34dBu (15.5mV); CD (Stereo): -34dBu (15.5mV); POWER AMP INPUTS: +8dBu (1.95V)

Displays

128 x 64 pixels, OLED

Maximum Output Voltage

74 Vrms

Maximum SPL

MIC inputs: +21dBu; Mono Line inputs: +41dBu; Stereo Line inputs: +30dBu; All other inputs: +22dBu; All other outputs: +22dBu

Channels

18

Phantom Power

48VDC

Auxiliarys (MON, FX, AUX)

2 Pre, 2 Post, 2 Pre/Post switchable

CMRR, MIC input, 1 kHz

>80dB

Shipping Weight

22

Input Impedances

MIC: 2㏀; Insert Return: 3.3㏀; 2Track Return & CD In: 10㏀; All other inputs: > 15㏀

Operating Temperature Range

+5 °C…+40 °C (40 °F…105 °F)

Output Impedances

Phones: 47Ω; All other outputs: 75Ω (unbalanced), 150Ω (balanced)

Equivalent Input Noise, MIC input, A-weighted, 150 ohms

-130dBu

Rated output power (*rated load) THD < 0.2%, 20Hz – 20kHz

into 4Ω: 2 x 900W; into 8Ω: 2 x 450W

Noise, Channel inputs to Master A L/R outputs, A-weighted

Master fader down: -97dBu; Master fader 0dB, Channel fader down: -87dBu; Master fader 0dB, Channel fader 0dB, Channel gain unity: -81dBu

Equalization

LO Shelving: ±15dB / 60Hz; MID Peaking, mono inputs: ±15dB / 100Hz to 8kHz; MID Peaking, stereo inputs: ±12 dB / 2.4 kHz; HI Shelving: ±15 dB / 12 kHz; Master EQ 11-band (63, 125, 250, 400, 630, 1k, 1.6k, 2.5k, 4k, 6.3k, 12kHz): ±10dB/Q = 1.5 to

Filter

LO-CUT, mono inputs: f=80Hz, 18dB/oct.; VOICE FILTER, mono inputs: switchable; FEEDBACK FILTER, MON ½: 70Hz to 7kHz, Notch, -9dB; Speaker Processing: LPN, switchable

Effects

Type: Dual stereo 24/48-bit multi effects processors; Effects presets: 100 Factory + 20 User, Tap-Delay; Remote control: Footswitch, MIDI

Digital Audio Interface

Channels: 4 In / 4 Out; AD/DA Conversion: 24-bit; Sampling Rate: 44.1 / 48 / 88.2 / 96kHz; PC Interface: USB2.0, Female Type B; Peak Display: 6 dB before Clip

MIDI Interface

5-pin DIN connector, In / Out

Protection

Mixer Outputs (Relay controlled): MON 1, MON 2, MASTER A; Amplifier: Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Turn-on Delay, Back EMF; Switching Mode Power Supply (μC controlled): Inrush Current Limiters, Mains Over/

Safety Class

I

Max. Single Channel Output Power, Dynamic-Headroom, IHF-A

into 2.66Ω: 2 x 1600W; into 4Ω: 2 x 1250W; into 8Ω: 2 x 675W