8 x 1250 w multi‑channel installation dsp class‑d amplifier

  • 8 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply.
  • Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive.
  • Dante and OCA integration via OMNEO with fallback options.
  • Parallel, bridged and parallel-bridged drive modes with 70/100V/140V/200V and low impedance operation
  • High efficiency Eco Rail technology for lower operating costs

IPX series are dedicated amplifiers for fixed install application such as e.g. stadiums, arenas, houses of worship, concert halls, theaters and other applications that require high‑power multichannel amplifiers with sophisticated speaker processing. The integrated DSP can run either in 48 kHz or true 96 kHz including FIR Drive. Besides analog inputs also Dante and OCA via OMNEO network inputs are available. Comprehensive fallback options allow redundant scenarios.

Each channel can be individually operated in low impedance mode, or 70V/100V Direct Drive mode. By bridging also 140V/200V Direct Drive is available. By the possibility to parallel two channels and parallel‑bridge four channels all kind of loudspeakers can be driven.

Due to the digitally controlled interleaved PFC supply reliable operation is ensured even under challenging mains supply situations. Reactive current is limited to a minimum, which reduces costs for mains installations and mains fusing in the installation.

In case of idle mode or light mode operation IPX series amplifiers automatically switch to a lower Eco Rail further reducing operating costs. In Eco Mode the amplifiers stay fully functional and supervised.

While IPX series amplifiers are fully integrated in IRIS‑Net, a OLED display on the front panel allows quick local control and supervision of the amplifier.

The connectivity of IPX series amplifiers is optimized for fixed install applications.


Amplifier Model IPX10:8
Low-Z mode: Load Impedance 2Ω 2.7Ω 4Ω 8Ω
Maximum Output Power1
Normal Mode, all channels driven 1300 W 1500 W 1250 W 1250 W
Bridged - - 2600 W 2500 W
Parallel 2500 W 3000 W 2500 W 1250 W
Parallel-Bridged 5200 W 6000 W 5000 W 5000 W
Direct Drive Mode: Nominal Voltage 70 V 100 V 140 V2 200 V2
Maximum Output Power1 1250 W 1250 W 2500 W 2500 W
Number of amplifier channels 8
Maximum Output Voltage, Normal mode, per channel 150 Vpeak
Maximum Output Current, Normal mode, per channel 41 Apeak
Voltage Gain
Low-Z mode, ref. 1 kHz 32.0 dB, adjustable 20.0 — 44.0 dB
Direct Drive mode 33.2 / 36.2 / 39.2 / 42.2 dB for 70 / 100 / 140 / 200 V
Input Sensitivity
Low-Z mode, Max. Output Voltage 10.7 dBu (2.66 V), adjustable -1.3 — 22.7 dBu
Direct Drive mode 6 dBu (1.55 V), fixed
THD 3 dB below max, AES17, 1 kHz < 0.05 %
DIM 100 3.15 kHz, 15 kHz < 0.15 %
IMD-SMPTE, 60 Hz, 7 kHz < 0.05 %
Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ω < -80 dB
Frequency Response, ref. 1 kHz, analog in to speaker out 20 Hz to 20 kHz (±0.5 dB)
Damping Factor, 20 Hz to 200 Hz, 8 ± > 400
Output Stage Topology Class D, fixed frequency
Signal to Noise Ratio Amplifier
A-weighted, analog input 112 dB
A-weighted, digital input 115 dB
Output Noise
A-weighted, analog input < -70 dBu
A-weighted, digital input < -73 dBu
Analog Audio Input/Thru
Type 4 x 6-pin Euroblock, male
Maximum Input Level +21 dBu
Input Impedance, active balanced 20 ㏀
Reference level equal to digital input +21 dBu for 0 dBFS
Speaker Output 2 x 8-pin Euroblock, 6mm, female
Power Consumption
Rated power consumption (see BTU table) 1300 W
⅛ Maximum Output Power at 4 Ω 1780 W
Idle Mode (no input signal) 105 W
Standby Mode < 18 W
Dimensions (W x H x D), mm 483 x 88.1 x 514.2
Weight 16.8 kg (37.1 lb)
Shipping Weight 19.1 kg (42.1 lb)
Sampling Rate 48 kHz / 96 kHz, OMNEO/Dante synchronized
Signal delay/latency Analog In to Speaker Out, 48 kHz/96 kHz 0.70 ms / 0.53 ms
Dante Network Latency typ. 1.00 ms
Signal Processing
User EQ 12 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, HiPass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type
User Delay 0 to 2000 ms per channel (units: µs, ms, s, cm, m, inches, feet)
Array EQ 5 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, LoShelvQ, HiShelvQ, Lo-Pass & All-Pass
Array Delay 0 to 500 ms per channel (units: µs, ms, s, cm, m, inches, feet)
Speaker EQ 10 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, Lo-Pass & All-Pass
Speaker X-Over Hi-Pass, & Lo-Pass per dB channel, 6/12/18/24/30/36/42/48 dB Bessel/ Butterworth, 12/24/48 Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel
Speaker FIR Up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker Limiters Peak Anticipation Limiter & RMS/TEMP Limiter per channel
Other Functions Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Pilot Tone Generator & Detection, Level Meters, Impedance Measurement & Load Monitoring
DSP Presets 1 factory preset + 20 user presetsr
Speaker-Pool Presets 30 speaker settings
Source Supervision & Fallback Pilot Tone supervision at Analog & OMNEO/Dante inputs, switchover to alternative Source Selection
Type 2 x Neutrik EtherCON/RJ45, redundant PRIMARY/SECONDARY
General 1000base-T/100base-TX, integrated switch
Network Audio Inputs 8 channels, 48/96 kHz, OMNEO/Dante format
Network Audio Outputs (Monitor) 2 channels, 48/96 kHz, OMNEO/Dante format
Mains Input 1 x Neutrik powerCON-HC
GPIO Control Port
Type 1 x 8-pin Euroblock, male
Ports & Operating Modes 3 x GPIO, switchable Analog In/Digital In/Digital Out
Analog Input Range 0 V to +13 V, 40 ㏀ input resistance
Digital Input Limits ON: < 1.5 V /
OFF: > 2.0 V, internal Pull Up (10 ㏀)
Digital Outputs ON: Output switched to GND, max. 200 mA
OFF: Open Collector (40 ㏀ to GND)
Reference Voltage Output +10 V, max. 200 mA, supervised, short circuit protected
READY/FAULT contact Galvanic isolated relay, max. 30 VDC/500 mADC
User Interface
Display Black/white OLED 256 x 64
Front panel indicators 4 x status LEDs (POWER, STANDBY, FAULT, OMNEO)
Front panel operating elements 3 buttons (UP, ENTER, DOWN)
Rear panel indicators 1 x status LED (STATUS)
Rear panel operating elements Mains Switch
Power Requirements 100 V to 240 V, 50 Hz to 60 Hz AC
Power Supply Topology Switching Mode Power Supply with digital controlled Power Factor Correction
Protections Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over-/Under voltage Protection
Cooling Front-to-rear, temperature controlled fans, supervised
Ambient Temperature Limits +5 °C to +40 °C (+40 °F to +105 °F)
IEC Protection Class Class I (grounded)
Electromagnetical Environment E1, E2, E3
Color Black
Amplifier at rated conditions, Low-Z Normal operation mode, all channels driven, 4 Ω loads, Analog input, 32 dB Gain, 48 kHz sample rate, unless otherwise specified
1Test signal for max. output power according IHFA-202 (Dynamic-Headroom, burst 1 kHz / 20 ms on / 480 ms off / low level -20 dB).
2Available in Bridged operation mode only.


Name Language Size Date
IPX 10_8 A&E Specification EN 61KB 11.24.2020
Name Language Size Date
Dynacord Amplifiers, Digital Audio Matrices, Software & Mixers Catalog EMEA DE 4.18MB 09.07.2020
Dynacord Amplifiers, Digital Audio Matrices, Software & Mixers Catalog EMEA EN 4.01MB 09.07.2020
Dynacord amplifiers, digital audio matrixes, software & mixers catalog 2019 PL PL 10.26MB 12.17.2019
Dynacord amplifiers, digital audio matrixes, software & mixers catalog 2019 RO RO 6.32MB 11.12.2019
Dynacord Elektronik Katalog DE 3.92MB 02.05.2020
Dynacord IPX10: 8 Testbericht DE 4.38MB 09.10.2019
Dynacord IPX10:8 Review EN 3.23MB 09.10.2019
IPX Brochure EN 1.2MB 02.16.2018
Retail catalog EMEA EN 59.07MB 11.10.2020
Retail catalog EMEA DE 29.85MB 11.10.2020
Name Language Size Date
IPX Amplifier Series EC Declaration of Conformity EN 11.09MB 01.28.2020
Name Size Date
IPX Series CAD Drawing DWG 1.3MB 02.11.2019
Name Language Size Date
IPX10:8 Hoja de Datos de Ingeniería ES 642KB 07.11.2018
IPX10:8 Datenblatt DE 622KB 07.11.2018
IPX10:8 Engineering Data Sheet EN 1.68MB 04.25.2018
IPX10:8 Engineering Data Sheet IT 621KB 07.11.2018
IPX10:8 Engineering Data Sheet PT 629KB 07.11.2018
IPX10:8 Engineering Data Sheet TR 623KB 07.11.2018
IPX10:8 Engineering Data Sheet KO 730KB 09.06.2018
IPX10:8 Fiche Technique FR 637KB 07.11.2018
IPX10:8 データシート JA 675KB 09.06.2018
IPX10:8 数据表 ZH 689KB 08.06.2018
Name Language Size Date
IPX & TGX Firmware v1.1 EN 43.95MB 03.11.2019
Name Language Size Date
System solutions Medium outdoor sports venue EN 899KB 02.25.2020
Name Language Size Date
IPX Series Manual ES 1.83MB 06.29.2018
IPX Series DSP Multichannel Networking Power Amplifier TR 1.76MB 06.29.2018
IPX Series DSP Multichannel Networking Power Amplifier IT 1.76MB 06.29.2018
IPX Series DSP Multichannel Networking Power Amplifier DE 1.85MB 06.29.2018
IPX Series DSP Multichannel Networking Power Amplifier ZH 2.07MB 06.29.2018
IPX Series Guide FR 1.77MB 06.29.2018
IPX Series Installation Manual EN 1.81MB 10.17.2019
IPX Series Manual PT 1.85MB 06.29.2018
IPX Series マニュアル JA 1.89MB 06.29.2018
IPX Series 설치 매뉴얼 KO 1.8MB 06.29.2018
Name Language Size Date
Mains Operation & Resulting Temperature Table & Mains Fusing IPX-Series Amplifiers EN 47KB 10.19.2018

IPX10-8 persp left 2400px

IPX10-8 front 2400px

IPX10-8 persp front 2400px

IPX10-8 persp right 2400px

IPX10-8 rear 2400px

Name Size Date
IPX Amplifiers Q-Sys Plug-In 1.4 3MB 03.03.2021
Name Language Size Date
Allgemeine Lieferbedingungen DE 184KB 11.30.2016
General Terms & Conditions of Deliver for Export Business EN 57KB 11.26.2014
Service Policies for Asia/Pacific Rim EN 2.62MB 09.04.2018
Service Policies for China EN 229KB 04.25.2013
Warranty conditions for Dynacord products in Europe, the Middle East, & Africa EN 195KB 09.29.2020
Warranty conditions for Dynacord products in Europe, the Middle East, & Africa DE 515KB 06.19.2019
Warranty conditions for Dynacord products in North America EN 159KB 09.14.2020
Name Size Date
Loudspeaker Settings 1KB 09.23.2020
SONICUE 1.2 291.62MB 09.24.2020
sprites_global sprites_ev