V Series
Go compact, amplify smart
- Four-channel and two-channel amplifiers, with a total powerTANK capacity of 600 W
- Variable Load Drive (VLD) providing the same power into 4 Ω, 8 Ω, 70 V or 100 V
- ecoRAIL and APD deliver significant reduction in power consumption
- dualCOOL convection cooling with additional intelligent fan in case of extreme thermal conditions
Designed with commercial applications in mind, V Series models are ideal for small to mid-sized installation scenarios. These compact amplifiers are not only designed for background music and announcements – they also excel when higher SPL levels are needed. Equipped with a range of cutting-edge Dynacord technologies to ensure flawless, silent operation and energy-saving, flexible power consumption, the V Series features two- and four-channel versions with different footprints that make them perfectly suited for a variety of installations.
Dynacord powerTANK technology adds even more installation flexibility, working like a power reservoir for the amplifier. With direct access to the total power of 600 watts, V Series can deliver asymmetric power across all channels as needed. There is no waste of energy, which allows great flexibility – especially when driving multiple audio zones with different loads. For example, a single V600:4 can simultaneously serve as system drive for the compact loudspeakers in a small zone (such as a kitchen area) as well as for larger loudspeakers (such as in an auditorium). Contributing to the ease of installation, this feature does not require any special configuration skills – powerTANK engages automatically. In conjunction with a DSP matrix – such as the Dynacord MXE5-64 Matrix Mix Engine – V Series amplifiers can also be specified for larger distributed installations working as a distribution amplifier for smaller zones.
产品
V600:2 |
V600:4 |
|
ELECTRICAL | ||
Total rated output power1 | 600 W | |
Number of channels | 2 | 4 |
Rated output power1 | 2 x 300 W | 4 x 150 W |
Output power: | 4 Ω / 8 Ω / 70 V / 100 V | |
Maximum output power per channel (power sharing) | 500 W / 600 W / 500 W / 600 W | |
AMPLIFIER | ||
4 Ω / 8 Ω / 70 V / 100 V | ||
Nominal Gain (+6 dBu input sensitivity, LEVEL 0 dB) |
27.0 dB / 30.0 dB / 33.2 dB / 36.2 dB | 24.0 dB / 27.0 dB / 33.2 dB / 36.2 dB |
Signal to Noise Ratio (A‑weighted, ref. to rated output power, LEVEL 0 dB) |
> -100 dB / > 102 dB / > 101 dB / > 103 dB | > -98 dB / > 100 dB / > 101 dB / > 103 dB |
THD+N (1/8 RATED OUTPUT POWER, 1 KHZ) |
< 0.1 % | |
CONNECTIVITY | ||
Type | 1 x 6-pin Euroblock, 3.81 mm, male, parallel 1x RJ45 (AES72-1E) |
2 x 6-pin Euroblock, 3.81 mm, male, parallel 1x RJ45 (AES72-1E) |
Loudspeaker output | 2 x 4-pin Euroblock, 5.08 mm, female | |
Control port type | 1 x 5-pin Euroblock, 3.81 mm, male | |
GENERAL | ||
Signal processing | Input Routing, Filter (24 dB/Oct.), Hi-pass 30/50/100/150 Hz, Lo-pass 150 Hz, Peak Limiter | |
Power requirements | 100 V to 240 V, 50 Hz to 60 Hz AC | |
Power consumption: | ||
Idle mode (ecoRAIL with no input signal) | < 12 W | < 20 W |
Consumption at 1/8 rated output power | 115 W | |
Standby mode (APD active) | < 1 W | |
Protections | Audio limiters, high temperature, DC, HF, short circuit, back-EMF, peak current limiters, inrush current limiters, mains over/under voltage protection | |
1 Test signal for max. output power according IHF-A-202 (Dynamic-Headroom, burst 1 kHz / 20 ms on / 480 ms off / low level -20 dB) |
下载
售后及相关政策